The Art of Plumbing Fundamentals When You Install a Bathtub
The Art of Plumbing Fundamentals When You Install a Bathtub
Blog Article
Presented here down the page you can find additional wonderful material involving How to Install a Bathtub Yourself.
Installing a bath tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a new one is likewise a moderately tough task. If the old bathtub is easily obtainable, the task can relocate immediately; if you need to open up a wall to get rid of the old bathtub and also place the new bathtub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will require a helper to leave the old tub as well as set in the brand-new one. See to it you have certified on your own for the work as well as are comfortable trying it. Rather than employing a service provider to take over a halfway-completed task, it is much better to consider utilizing one prior to you begin. Chances are you might need a specialist plumber to make tube links.
This post will certainly help you install a new bathtub in your restroom if you have already bought a new bathtub as well as don't need to transform the setup of your previous supply of water pipes.
Your tools and material list need to comprise the following:
Getting ready for the Installment
Firstly, the supporting framework provided with the bath needs to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps unit to stop pressure on the bathtub.
Fit the flexible tap connectors to the bottom of both taps utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its last position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be quite problematic because of the restricted access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly come from the pipelines. Once the supply pipes have been removed, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning throughout this process. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing substance.
Prior to going on to fit the new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bathtub
Using the two wood boards under its feet, put the bath tub in the needed position. The wooden boards are valuable in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the level and adjusting the feet on the bathtub till the level reviews degree.
To install taps, fit the bottom of the outermost versatile faucet connector to the proper supply pipe by making a compression join; then do the very same for the other tap.
Activate the water supply and also check all joints and brand-new pipework for leaks and also tighten them if necessary. Load the bathtub as well as also examine the overflow outlet and the regular outlet for leaks.
Lastly, fix the bathroom paneling as explained in the supplier's instruction manual. Tiling and also securing around the tub should wait until the bathtub has been made use of at least when as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a link to the existent supply pipes.
If you need to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin making certain that the washers are in location between the tap and the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former type should be attached to the faucet ends initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a stiff seal, triggering the water to permeate the wall in between the bathroom and also the tiling, bring about issues with moisture and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to enable the activity experienced when the tub is in usage. The sealant can split relatively very early if you do not consider this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise conveniently readily available on the market. It is recommended to fit the tiles using water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been brought to that report on A Step-by-Step Guide to Installing a Bathtub from a friend on another site. Feel free to take a moment to promote this page if you appreciated it. Thank-you for taking the time to read it.
Expertise on line! Report this page